Boat Haul Out Services in Pensacola, FL
Need your boat hauled out? Revolutions Marine provides full-service boat haul outs at our facility inside Pelican’s Perch Marina and Boatyard on Bayou Chico in Pensacola. From bottom painting and hull repairs to running gear service and hurricane prep, we handle everything while your vessel is on the hard.
Ready to Get Your Boat Out of the Water but Not Sure Where to Start?
- Is marine growth slowing your boat down and killing your fuel economy?
- Has your bottom paint worn thin or started blistering after a few seasons in the water?
- Did you hit something near the pass and need to check your hull, prop, and shaft?
- Do you need a haul out for a pre-purchase survey or insurance inspection?
- Is hurricane season approaching and you need your vessel out of the water and secured on land?
Whatever the reason, Revolutions Marine coordinates the entire haul out and handles all the work on site so you don’t have to chase down five different contractors.
Pensacola Boat Haul Out Services Done Right
Our shop sits inside a working boatyard with a 50-ton Marine Travel Lift, on-site repair space, and direct waterfront access on Bayou Chico. When your boat comes out of the water, our technicians are already here to inspect it, diagnose what it needs, and get the work done — all under one roof.
We haul and service everything from small center consoles and bay boats to large sailboats and yachts up to 60 feet.
Bottom Painting
We pressure wash, sand, prep, and apply fresh antifouling bottom paint to protect your hull from barnacles, algae, and marine growth. We use quality ablative and hard paints based on your vessel and how it’s used.
Hull Inspection
While your boat is on the hard, we inspect for blistering, gelcoat damage, stress cracks, and grounding impacts. Our fiberglass repair team handles everything from cosmetic gelcoat work to full transom and stringer rebuilds.
Running Gear Service
We inspect and service your prop, shaft, strut, cutlass bearing, and rudder. Revolutions Marine is one of the only shops in Pensacola that can perform cutlass bearing replacement — it requires specialized tooling and a vessel on the hard.
Zinc Anode Replacement
We check all sacrificial anodes on your hull, shaft, and trim tabs. Anything more than 50% depleted gets replaced. We also install PropSpeed and foul-release coatings on underwater metals.
Cutlass Bearing Replacement
Cutlass bearing replacement is a specialized marine repair service that removes and replaces worn rubber-lined propeller shaft bearings to eliminate vibration and shaft play, backed by our status as one of the very few local shops in Pensacola equipped to perform this complex job.
Thru-Hull and Seacock Inspection
We inspect every below-waterline fitting for corrosion, dezincification, and proper operation. Failed or questionable thru-hulls get replaced before they become an emergency.
Hurricane Haul Out
When a named storm threatens the Gulf Coast, we provide haul out and secure on-land storage at our Bayou Chico facility. We block your vessel on jack stands, remove canvas, and take steps to protect against wind and surge damage. Contact us early in the season to get on the list.
Survey Haul Outs
Buying a boat or renewing insurance? We coordinate haul outs for marine surveyors and buyers so the vessel is lifted, positioned, and available for inspection and sea trial.
Shaft Seal Replacement
As an authorized PSS installer, we fit the world’s #1 selling marine shaft seal to keep your bilge dry and your driveline running clean. The PSS is a packless mechanical seal that replaces the traditional stuffing box — meaning no more constant packing adjustments, no shaft scoring, and a 100% watertight seal. Its design absorbs shaft misalignment, vibration, and propeller thrust, and it’s certified by ABS, Bureau Veritas, and RINA. Factory-trained installation means it’s done right and your warranty stays intact.
Propspeed Installation
We’re a certified Propspeed applicator, protecting your propeller, shaft, and running gear from marine growth. Propspeed is a foul-release coating — not an antifouling paint — that bonds an etching primer and ultra-slick silicone topcoat to underwater metals, so barnacles and weed can’t grip. The result: better fuel efficiency, more speed, less drag, and a clean prop at haul-out. It’s biocide-free and safe for marine life. Because results depend on precise surface prep and timing, our trained technicians apply it the right way for maximum performance and longevity.
SeaHawk Applicator
We’re a Sea Hawk Certified Applicator, delivering professional antifouling bottom paint application for boats, yachts, and workboats. Sea Hawk’s marine coatings — including the Cukote and Tropikote lines — protect your hull below the waterline from barnacles, slime, and marine growth, with self-polishing ablative and hard formulas matched to your vessel, water, and fouling conditions. Proper surface prep and application are what make antifouling paint last — and as a certified applicator, we’re one of the few yards able to back the work with Sea Hawk’s Antifouling Paint Written Guarantee. Less growth, fewer haul-outs, a smoother, faster hull.
Trusted by Seatow
When Sea Tow brings a vessel in, they bring it to a yard they trust. We handle haul-outs and general boat repair and maintenance for Sea Tow and the boaters they tow in — hauling, blocking, and getting your boat back in the water safely. From engine and running-gear repairs to hull work, bottom service, and routine maintenance, our experienced marine technicians keep recreational and working vessels running. Fast turnaround, dependable workmanship, and the kind of service that earns the trust of the pros who are on the water every day.
How It Works
02
2
Step 2
We will contact you within 24 hours to schedule your haul out and provide a written estimate for the required work to be completed/
03
3
Step 3
We complete the work, you enjoy your boat without the stress and hassle of doing repairs yourself.
